- Zte mf70 firmware update install#
- Zte mf70 firmware update trial#
- Zte mf70 firmware update Pc#
- Zte mf70 firmware update plus#
This means you don't need a PC or laptop to use it, just slot it into a USB power adapter to plug it into a wall socket for when you're at home or in the office. Up to 10 devices can connect to it simultaneously and there is no connection manager or complex start up procedure. Just put a SIM card into the MF70 and connect it to a USB power source and your away, no setup needed.
Zte mf70 firmware update plus#
The ZTE MF70 is a 3G dongle plus Wi-Fi modem and router in one, giving you your own personal Wi-Fi hotspot when plugged into the USB power supply provided, or a USB dongle when plugged into a laptop. Weight less than 30g, The MF70 Hotspot MiFi enable 10 wifi devices surfing at the same time. No rollback needed.įinal note : Credit goes to Madvinegar at this forum whose comments on mode-switching helped to assuage my doubts.ZTE MF70 is the latest mobile WiFi hotspot for both 3G and 2G nets. PPS My Pineapple is using firmware 1.1.1. PS I did not have to make a ttyUSB n folder nor put anything in it.
Zte mf70 firmware update trial#
Now that I've successfully concluded the last two days of soul-destroying trial and error, I'd better go and make up with my other half! Some users might find that one or two of the steps are superfluous (sorry).Įither way I hope they serve as helpful pointers to anyone struggling the way I did. Please note that the order of these steps is mostly correct if not 100% correct. I then tried the same with my Kali laptop and my two smart phones and was able to do the same with them too. On my Windows laptop using either Firefox or Internet Explorer I was able to surf the net while wirelessly connected to the Pineapple. I disconnected the LAN cable from my Pineapple and connected my laptop to it wirelessly instead, then PuTTYed back into the Pineapple again and typed the Linux command ping 8.8.8.8 - which worked!ġ5. I clicked Network > Mobile Broadband and changed the settings to those shown here:ĪPN: ġ4. Using Firefox I went to the Pineapple's web interface (172.16.42.1:1471).ġ3. I then saved and exited the file and also exited PuTTY too.ġ2. Thankfully the VID (19d2) was already correct but the dongle name and PID needed changing to MF respectively.ġ1. To create a new file with the name 19d2:1405 but based on 19d2:1224 file I ran the Linux command: As there was no such file in the list, I looked for a file whose name came close to my dongle's, but before it in sequence (19d2:1224 was closest).ĩ. Still at the Pineapple's Linux command line I ran the commands:Īnd searched the list shown for a file that corresponded to my dongle's xxxx:xxxx number. At the Pineapple's Linux command line I ran the commandĪnd made a note of the xxxx:xxxx hex number corresponding to my dongle (in my case 19d2:1405)Ĩ. I then plugged my dongle back into the Pineapple.ħ. Presumably this meant the mode-switch had worked.Ħ. Discovered that after running these commands I could plug the dongle straight into a laptop (Windows/Linux) and got an immediate connection to the internet without having to do anything else.
Zte mf70 firmware update install#
Opkg install comgt kmod-usb-serial kmod-usb-serial-option kmod-usb-serial-wwan usb-modeswitchĥ.
PuTTYed into the Pineapple's Linux command line. I made sure that my Pineapple could share my Windows laptop's internet connection and that they were physically connected to each other by a LAN cable.ģ. From memory, this is what I did from scratch to make it work:ġ.
0 kommentar(er)
